Description
3M Die Grinder 28629 Pneumatic Power 0.3 HP Motor 1/4" Collet 25000 RPM USA
Product Features Straight shaft tool with narrow collet allows access to hard-to-reach spaces with products such as cartridge rolls and cross buffs Precision-balanced steel motor reduces vibration for greater efficiency and operator comfort 3M Gripping Material on the body reduces vibration and enables operator to maintain a secure grip with less effort Directional exhaust suits operator preference This 3M(TM) straight shaft, tool has been extended 3-inches allow operator to get into hard to reach areas. Lightweight 0.3 horsepower pneumatic die grinder is designed to efficiently perform a variety of polishing, buffing, shaping, and deburring functions. Powerful and light-weight tool. Off-set gear box for increased torque. Gripping material for greater operator comfort. Safety lever throttle to avoid accidental starting. Ideal for medium-duty applications. 1/4-inches air inlet thread size. This 0.3 horsepower, 25000 RPM die grinder has rear exhaust, comes standard with 1/4-inches collet size, as well as a 1/8-inches collet insert, a 1/4-inches to 1/8-inches reduction bushing, and 2 wrenches. The 3M™ Die Grinder 28629 is a straight shaft tool ideal for accessing hard-to-reach areas for medium-duty applications such as deburring, shaping, buffing, and polishing. This pneumatic tool has an efficient 0.3 hp motor and is designed for continuous use with features that enhance operator comfort and control. The precision-balanced steel motor reduces vibration and creates a lighter weight tool, while 3M™ Gripping Material on the body further reduces vibration and enables a secure grip with less effort. The adjustable directional exhaust allows airflow to be directed in any direction preferred, even toward the operator for cooling if desired. The 3M Die Grinder 28629 comes with an off-set gear box for increased torque, a standard 1/4" collet as well as a 1/8" collet insert, and a 1/4" to 1/8" reduction bushing. To prevent accidental starting, the grinder incorporates a safety lever. Length is 6" and Max RPM is 25,000 at 90 psi. Use with accessories that have a max RPM of 25,000 or greater. A die grinder is a handheld power tool that runs spindle-mounted abrasives such as coated abrasives or nonwoven surface conditioning abrasives. Typical coated abrasive products that can be run on a die grinder include cartridge rolls for reaching tight corners and crevices, cross pads for sanding small internal diameters, and evenrun bands and flap wheels for sanding and polishing contours. Scotch-Brite™ surface conditioning products typically used include radial bristle discs, combi wheels, and cross buffs for removing rust and debris from internal diameters of small cylinders. These are just a few of a multitude of products that can be run on a die grinder. The Die Grinder 28629 requires a clean lubricated air supply that will give a measured air pressure at the tool of 6.2 bar (90 psi) when the tool is running with the lever fully depressed so the maximum RPM is not exceeded. The tool can be run at lower pressures but should never be run higher than 6.2 bar (90 psi). If run at a lower pressure the performance of the tool is reduced. For pneumatic power to the tool, an approved 10 mm (3/8 inch) x 8 m (25 feet) maximum length airline is recommended. The tool must be connected to an airline system with an easily accessible air shut off valve. It is strongly recommended that an air filter, regulator, and lubricator (FRL) be used to supply clean, lubricated air at the correct pressure to the tool. An appropriate air pressure regulator must be used at all times while operating this tool when the supply pressure exceeds the marked maximum of the tool, 25,000 RPM. If such equipment is not used, the tool should be manually lubricated. For instructions on connecting the tool to the air supply and manually lubricating the tool, see the Instruction Manual.